MiniUnix/usr/man/man4/tty.4

Find at most related files.
including files from this version of Unix. 
.th TTY IV 5/27/74
.sh NAME
tty \*- general typewriter interface
.sh DESCRIPTION
This section describes
both a particular special file,
and the general nature of the typewriter interface.
.s3
The file
.it /dev/tty
is, in each process, a synonym
for the control typewriter associated with that process.
It is useful for programs or Shell sequences which wish to
be sure of writing messages on the typewriter
no matter how output has been redirected.
It can also be used for programs which demand a file name
for output, when typed output is desired
and it is tiresome to find out which typewriter
is currently in use.
.s3
As for typewriters in general: all of the low-speed asynchronous
communications ports use the
same general interface, no matter what
hardware is involved.
The remainder of this section discusses
the common features of the interface;
the KL, DC, and DH writeups (IV) describe
peculiarities of the individual devices.
.s3
When a typewriter file is opened, it causes
the process to wait until a connection is established.
In practice user's programs seldom open these
files; they are opened by
.it init
and become a user's
input and output file.
The very first typewriter file open in a process becomes
the
.it "control typewriter"
for that process.  The control typewriter plays a special
role in handling quit or interrupt signals, as discussed
below.
The control typewriter is inherited by a child process during a
.it fork.
.s3
A terminal associated with one of these files ordinarily
operates in full-duplex mode.  Characters may be typed at any time,
even while output is occurring, and are only lost when the
system's character input buffers become completely
choked, which is rare,
or when the user has accumulated the maximum allowed number of
input characters which have not yet been read by some program.
Currently this limit is 256 characters.
When the input limit is reached all the
saved characters are thrown away without notice.
.s3
These special files have a number of modes which can be changed
by use of the
.it stty
system call (II).
When first opened,
the interface mode is
300 baud;
either parity accepted;
10 bits/character (one stop bit);
and newline action character.
Modes that can be changed by
.it stty
include
the interface speed (if the hardware permits);
acceptance of even parity, odd parity, or both;
a raw mode in which all characters may be read one at a time;
a carriage return (CR) mode in which
CR is mapped into newline on input and
either CR or line feed (LF) cause echoing of
the sequence LF-CR;
mapping of upper case letters into lower case;
suppression of echoing;
a variety of delays after function characters;
and the printing of tabs as spaces.
See
.it getty
(VIII)
for the way that terminal speed and type are detected.
.s3
Normally, typewriter input is processed in units of lines.
This means that a program attempting
to read will be suspended until an entire line has been
typed.  Also, no matter how many characters are requested
in the read call, at most one line will be returned.
It is not however necessary to read a whole line at
once; any number of characters may be
requested in a read, even one, without losing information.
.s3
During input, erase and kill processing is normally
done.
By default, the character `#' erases the
last character typed, except that it will not erase
beyond the beginning of a line or an EOT.
By default, the character `@' kills the entire
line up to the point where it was typed, but not beyond an EOT.  Both these
characters operate on a keystroke basis independently
of any backspacing or tabbing that may have been done.
Either `@' or `#' may be entered literally by preceding
it by `\\';
the erase or kill character remains, but the
`\\' disappears.
These two characters may be changed to others.
.s3
When desired,
all upper-case letters are mapped into
the corresponding lower-case letter.
The upper-case letter may be generated by preceding
it by `\\'.
In addition, the following escape sequences are generated
on output and accepted on input:
.s3
.lp +14 7
for	use
.lp +15 7
\*g	\\\*a
.lp +15 7
.br
|	\\!
.br
.tr ??
.lp +15 7
~	\\^
.lp +15 7
{	\\(
.lp +15 7
}	\\)
.s3
.i0
In raw mode,
the program
reading is awakened on each character.
No erase or kill processing is done;
and the EOT, quit and interrupt characters
are not treated specially.
The input parity bit is passed back to the reader,
but parity is still generated for output characters.
.s3
The ASCII EOT (control-D) character may be used to generate an end of file
from a typewriter.
When an EOT is received, all the characters
waiting to be read are immediately passed to
the program, without waiting for a new-line,
and the EOT is discarded.
Thus if there are no characters waiting, which
is to say the EOT occurred at the beginning of a line,
zero characters will be passed back, and this is
the standard end-of-file indication.
The EOT is passed back unchanged in raw mode.
.s3
When the carrier signal from the dataset drops (usually
because the user has hung up his terminal)
a
.it hangup
signal is sent to all processes with the typewriter
as control typewriter.
Unless other arrangements have been made,
this signal causes the processes to terminate.
If the hangup signal is ignored, any read
returns with an end-of-file indication.
Thus programs which read a typewriter and test for
end-of-file on their input
can terminate appropriately when
hung up on.
.s3
Two characters have a special meaning when typed.
The ASCII DEL character (sometimes called `rubout')
is not passed to a program but generates
an
.it interrupt
signal
which is sent to all processes with the associated control typewriter.
Normally each such process is forced to terminate,
but arrangements may be made either to
ignore the signal or to receive a
trap to an agreed-upon location.
See
.it signal
(II).
.s3
The ASCII character FS generates the
.it quit
signal.
Its treatment is identical to the interrupt signal
except that unless a receiving process has
made other arrangements it will not only be terminated
but a core image file will be generated.
If you find it hard to type this character,
try control-\\ or control-shift-L.
.s3
When one or more
characters are written, they are actually transmitted
to the terminal as soon as previously-written characters
have finished typing.
Input characters are echoed by putting them in the output queue
as they arrive.
When a process produces characters more rapidly than they can be typed,
it will be suspended when its output queue exceeds some limit.
When the queue has drained down to some threshold
the program is resumed.
Even parity is always generated on output.
The EOT character is not transmitted
(except in raw mode)
to prevent terminals
which respond to it from hanging up.
.sh FILES
/dev/tty
.sh "SEE ALSO"
dc (IV), kl (IV), dh (IV), getty (VIII), stty (I, II), gtty (I, II), signal (II)
.sh BUGS
Half-duplex terminals are not supported.
On raw-mode output, parity should be transmitted as specified
in the characters written.